Home » Jeep » How to replace starter in a Jeep Grand Cherokee
Filed: Jeep

A starter motor 3.7L or 4.7L compress, drawing air and fuel into the cylinder of the Jeep Grand Cherokee, so they will ignite. It also gets the ignition and crankshaft into place so that the candles and fire the fuel injectors may be used. Therefore, a lack of starting the starter motor is prevented. Follow these steps to replace the starter in a Cherokee from 1999 to 2005 Jeep Grand.


Instructions
Remove the starter bad

  1. Park your Jeep Grand Cherokee on a level surface, activate the emergency brake and place blocks behind the rear tires for safety. Disconnect the negative battery extractor and a cable to isolate. Lift the front end of the car with a jack for easy access to the starter.
  2. Check a deposit, if your Jeep Grand Cherokee four-wheel drive (in some programs). You will find support between the front and side view of the machine. Remove the two bolts on the shifter bracket and the retaining clips on easy access to the bolts to get started. Put the screws in the glass for safe storage to remove later.
  3. Support the weight of the starter and remove the bolts start. Put the screws into the pot. Move the starter toward the front of the vehicle. The nose of the pinion of the starter housing should clarify the case.
  4. Point the nose of the starter and the starter down enough for the mother that the positive battery cable harness connector eyelet to take the pins attached magnetic battery connector to remove.
  5. Remove the positive battery cable and remove the solenoid valve connector pin / socket receptacle. Remove the starter motor of your Jeep Grand Cherokee.
  6. Take your starter defective parts to the store with you. Aftermarket distributors starters most reprocessing they sell, so you can probably get partial credit for your new starter by exchanging your old one. Make sure you take care not to damage the starter, because the better condition it is, the more you can get it.
  7. Purchase a replacement starter that has the ability handle the same or higher (power) as the starter home. Also correspond to the bolt patterns, drive gears and electrical connections. Your manual may or specifications of auto parts technician will help you determine them. Download a manual on the website my jeep.

Install the new starter

  1. Let the starter solenoid wire. Remember to support the weight of the starter at any time.
  2. Connect the battery cable to solenoid stud, nut and pull the battery cable.
  3. Position the starter next to the machine. If your Jeep Grand Cherokee equipped with an automatic transmission, put the hook in the cooling coil position. Install and remove the bolts securing the starter. Replace transmission range.
  4. Reduce your Jeep Grand Cherokee on the floor again. Connect the negative battery cable. Turn the key in the ignition, if your new starter is working properly.

Tips & Warnings

  • Always check the battery, alternator and solenoid valves to be sure they work properly before making a starter. When starting an engine, many do-it-yourself misdiagnose the problem as the starter and replace it unnecessarily, only to discover that the vehicle still does not start.
  • If you believe your starter is the problem, use a test to see if the starter turns and how well the starter is running. A test will check the amp load, voltage and RPM. When the starter is good, it will take 60 to 150 amps at idle and up to 250 amps under load.
  • ┬áIf your Jeep Grand Cherokee is a former model and / or high mileage, you should also replace the solenoid.
  • Never leave hanging the start of the wiring harness. Support to avoid the weight of the input at any time during the process of removal and installation to prevent damage to the starter or the wiring harness.
  • Do not operate the starter for more than 30 seconds at a time. Let the starter for at least two minutes between starting attempts to prevent permanent damage to the charges.
  • The starter replacement process is different for later models or those with a format other than motor the1999 to 2005 Jeep Grand Cherokee with 3.7L or 4.7L engine. Consult your owner’s manual or a mechanic for more details.

Related Post How to replace starter in a Jeep Grand Cherokee

1972-1973 Jeep CJ models, complete electrical wiring diagram

1983 Jeep “J” Pickup Truck Electrical Wiring Diagram

How to remove a radio in a factory Jeep Wrangler

How to Replace a Jeep Cherokee Thermostat

Problems with the Jeep Grand Cherokee